56 mm Neck Heel and 10 mm Tuner Holes on a Telecaster-Style Neck

By twtguitar November 2nd, 2026 54 views

Introduction: Measuring a neck pocket and checking tuner bushings before assembly turns four catalog numbers into a clear fit decision.

A replacement guitar neck can look right in a photo and still create hours of extra work if the heel, nut width, or tuner holes do not match the body and hardware on the bench. The useful approach is to treat the numbers as measurement points, not as a promise that every pocket and every set of tuning machines will line up. This guide walks through the 56 mm heel width, 26 mm heel depth, 43 mm nut width, and 10 mm tuner holes on a Telecaster-compatible neck, then explains where each measurement sits and why tolerance matters during assembly.

What 56 mm Heel Width and 26 mm Depth Measure on a Neck

The heel is the block-shaped end of the neck that sits inside the body pocket. Heel width is measured across that end, side to side, at the widest part that enters the pocket. On a Telecaster-style neck, 56 mm is a common starting point for that joint, and it is the number a builder compares with the pocket width. The measurement is taken across the back of the heel, not across the fretboard at the nut, and not across the wider body end of the fretboard extension. A caliper reading taken at the very end of the heel, square to the centerline, gives the most useful figure. Heel depth is the thickness of that same end, measured from the fretboard side down to the back of the neck. The listed 26 mm depth tells you how much material fills the pocket from top to bottom. That number matters because the pocket has a floor, the neck has a back curve, and the string height above the body depends on how those surfaces meet. A neck that is too deep can sit high in the pocket and push the strings away from the body. A neck that is too shallow can leave the heel sitting low or force the installer to use a shim. The 26 mm figure is therefore a vertical fit number, while the 56 mm figure is a side-to-side fit number. A common workshop observation is useful here: before assembly, a technician measures the empty pocket in several places, checks for finish buildup or rounded corners, and then dry-fits the neck without strings. The neck is pressed into the pocket, checked for side-to-side movement, and viewed from the bridge end to see whether the centerline points toward the bridge saddles. That routine turns the 56 mm and 26 mm specs into a practical question: does this particular pocket accept this particular heel with light hand pressure, or does it need scraping, sanding, or a shim? The numbers guide the check; the pocket itself decides the final fit. The 43 mm nut width belongs to the other end of the neck, but it is worth keeping in view because it defines the overall width at the first fret area. A neck can have a correct 56 mm heel and still feel wrong if the player expects a different nut width. The heel and nut are two ends of the same taper, and both should be read as part of the neck’s overall geometry rather than as isolated catalog facts.

How 10 mm Tuner Holes and 43 mm Nut Width Affect Hardware Alignment

Tuner holes and nut width are hardware-alignment numbers. The tuner holes control how the tuning machines sit on the headstock, while the nut width controls the overall string spread at the player’s hand. Both affect whether the finished instrument feels centered and whether the strings run cleanly from the nut to the tuners. A guitar neck store listing may show these figures next to the heel size, but they answer different assembly questions. The heel tells you whether the neck enters the body; the tuner holes and nut width tell you whether the hardware and strings will sit where the player expects.

1. How Tuner Hole Diameter Aligns With Modern Tuning Machines

A 10 mm tuner hole is a modern standard size for many current tuning machines. The hole is not the same as the tuner post diameter; it is the opening that accepts the bushing, collar, or press-fit sleeve on the face of the headstock. On a 10 mm hole, the bushing should pass through cleanly without excessive play. If the bushing is noticeably loose, the tuner can shift under string tension. If the bushing will not enter, the hole may need light reaming or the hardware may be a different size. The check is simple: remove the tuner, measure the bushing outer diameter, measure the hole, and test-fit one tuner before installing the set. Headstock thickness also belongs in that check. A bushing that fits a 10 mm hole can still sit too high or too low if the headstock face is thicker or thinner than the hardware expects. Washers and collars take up some space, but they cannot fix a hole that is the wrong diameter. For a Telecaster-style build, the tuner layout is usually six in line, so one test fit on the treble-side hole tells you a lot about the rest. The 10 mm figure is a useful compatibility marker, and it is most reliable when it is matched to the actual bushing diameter of the tuning machines going onto the neck.

2. Why Nut Width Matters to String Spacing at the Headstock

Nut width is the overall width of the neck at the nut, measured across the fretboard before the strings are installed. A 43 mm nut width is a familiar modern width for electric guitars, and it gives the player a certain amount of edge distance on the outer strings. The key point is that nut width does not by itself set the string spacing. The string slots in the nut do that. Two necks can share the same 43 mm width and still feel different if the slots are cut with different edge margins or different spacing between strings. That distinction matters during assembly because the nut is a setup part, not just a width number. The listed neck specs include the 43 mm width, while nut material and nut slotting are not confirmed for this particular neck. A builder should expect to check the nut height, slot depth, and string spacing during setup, especially if the neck arrives without a finished nut. The 43 mm width tells you the space available at the first fret; the slotting decides how the strings use that space. When the nut is right, the strings run straight to the tuners and the player feels a clean edge margin. When it is wrong, the guitar can feel cramped on one side or loose on the other even though the width number looks correct.

Why Measurement Tolerance Matters Before Installing a Replacement Neck

Tolerance is the small difference between the listed number and the actual surface on the bench. A neck pocket may be finished with a slight build-up of paint, a heel may have a rounded edge from sanding, and a 10 mm hole may measure a fraction differently depending on where the caliper sits. Those differences are normal in guitar assembly. They are also why a replacement guitar neck should be dry-fitted before screws, strings, or tuners are installed. The goal is not to force the neck into the pocket or to assume that a matching catalog number means zero adjustment. The goal is to find where the surfaces touch, where they rock, and whether the centerline points at the bridge. The heel screw holes and neck profile are not confirmed for this neck, so the installer should not assume a pre-drilled, drop-in joint. Some necks arrive with mounting holes, some do not, and the pocket on the body may already have a screw pattern. Dry-fitting first protects both parts. Check the heel width in the pocket, check the heel depth against the pocket floor, and look down the neck from the bridge end to confirm string alignment. If the neck sits too high, a shim or pocket adjustment may be needed. If the heel is tight in the pocket, light sanding may be safer than force. These are ordinary assembly steps, not defects. The same tolerance thinking applies to the tuner holes and the nut. A 10 mm hole that fits one brand of modern tuners may be tight or loose with another brand’s bushings. A 43 mm nut width gives the setup a known starting point, but the final string spacing still depends on the nut slots. After shipping, wood can move slightly with humidity, and a light fret check or minor fret dressing may be part of the setup. That is normal for a wooden instrument part. The listed 56 mm heel, 26 mm depth, 43 mm nut width, and 10 mm tuner holes are useful assembly landmarks, and the actual pocket, hardware, and setup decide the final fit.

Conclusion

The four numbers on a Telecaster-compatible neck describe four different contact points: the heel width across the pocket, the heel depth from fretboard to back, the nut width at the first fret, and the tuner hole diameter at the headstock. Reading them as measurement points makes assembly easier. Measure the pocket, test-fit one tuner bushing, check the nut width against the player’s preference, and expect a normal setup rather than a zero-adjustment install. A current example such as the TWT guitar quarter-sawn black wenge Telecaster-compatible neck with a rosewood fretboard lists these dimensions, which gives a builder a clear starting point for checking a body pocket and a set of tuning machines before assembly begins.

FAQ

Q: What does a 56 mm neck heel width measure on a Telecaster-style neck?

A: It measures the width of the heel end, side to side, at the part that enters the body pocket. The reading is taken across the back of the heel near the body joint, not at the nut. A 56 mm heel is a common Telecaster-style starting point, and it should be compared with the actual pocket width before installation.

Q: Are 10 mm tuner holes compatible with modern tuning machines?

A: In many cases, yes. A 10 mm hole is a common size for modern tuning machine bushings, but the bushing outer diameter and headstock thickness still need to match. Test-fit one tuner before installing the full set, and check that the bushing sits cleanly without excessive play or a forced fit.

Q: Does a 43 mm nut width affect string spacing and feel?

A: It affects the overall width at the nut and the space available for string spacing, but the nut slots set the actual string positions. A 43 mm width gives a familiar modern feel, while the final edge margin and spacing depend on how the nut is slotted and set up.

Sources / References

Luthiers Mercantile International

Trademark scope of protection | USPTO

TWT guitar Premium Telecaster Compatible Quarter Sawn Black Wenge Guitar Neck

Previous
9.5-Inch Radius and 25.5-Inch Scale on a Replacement Guitar Neck
Read More
Next
Rosewood Fretboard Feel and Appearance on Telecaster Replacement Necks
Read More